DESIGN BY PROGRAM ANSYS FLUENT PROCESSES IN HEATING OF CALDRON OF TPP-210А

Keywords: ANSYS FLUENT, modeling, solid fuel, combustion, coal, boiler furnace

Abstract

Numerical modeling of processes in the furnaces of power boilers serves as a tool for assessing the impact of the proposed structural or operational changes on the ongoing processes and characteristics of the boiler. Using the ANSYS FLUENT program, three-dimensional numerical simulation of anthracite combustion processes in the furnace of a TPP-210A boiler with liquid slag removal was performed. The initial data for the calculation — component costs, composition and calorific value of coal — are taken from the boiler passport for the nominal operating mode. Air suction into the furnace has been taken into account. As the boundary conditions on the walls of the furnace, their thermal resistances are set, the values of which are determined by the results of the zone calculation of the furnace by the normative method. The turbulence model was used in the modification of a realizable, non-premixed combustion model of particle combustion in a single mixture fractions formulation, discrete phase model of the movement of coal particles, P-1 emission model, two-competing-rates model of volatile output, kinetics/diffusion-limited model of coal combustion. Obtained as a result of the distribution of heat flux densities and wall surface temperatures («contaminants») within each of the zones is substantially uneven, which confirms the validity of the type of boundary condition used on the walls. The change in the height of the furnace of the mass-average temperature of the flow, the heat flux densities into the walls, the distribution of the mechanical underburning of the fuel along the height of the furnace according to the simulation results are compared with the data of a well-known experimental study of S.L.Shagalova and I.N.Shnitser processes in the boiler under consideration, as well as with the data of the zone calculation of the boiler by the normative method. On this basis, a conclusion was made about satisfactory simulation results. Ref. 12, Fig. 7, Tab. 3.

Downloads

Download data is not yet available.

Author Biography

M.M. Nekhamin, Coal Energy Technology Institute of National Academy of Sciences of Ukraine, Kyiv

Candidate of Technical Sciences

References

Аlvarez, L., Gharebaghi, M., Jones, J.M., Pour- kashanian, M., Williams, A., Riaza, J., Pevida, C., Pis, J.J., Rubiera, F. (2013). CFD modeling ofxy- coal combustion: Prediction of burnout, volatile and NO precursors release. Applied Energy, 104 (C), pp. 653–665.

Riccio, C., Simms, N.J., Oakey, J.E. (2019). Deposition prediction in a pilot scale pulverized fuel- fired combustor. Fuel, 253, pp. 1204–1213.

Ryoichi Kurose. (2009). Numerical Simulations of Pulverized Coal Combustion KONA Powder and Particle Journal, 27, pp. 144–156.

Troy Holland, Thomas H. Fletcher. (2017). A Comprehensive Model of Single Particle Pulverized Coal Combustion Extended to Oxy-coal Conditions. Energy Fuels, 31 (3), pp. 2722–2739.

Madejski, Р., Modliсski, N. (2018). Numerical investigation using two different CFD codes of pulverized-coal combustion process characteristic in an industrial power plant boiler. 13th International Conference on Boiler Technology, Szczyrk, Poland, 82, id. 01009.

Teplovoi raschet kotel‘nykh agregatov (normativnyi metod). Izdanie 2-e. Ed. N.V. Kuznetsov. Moscow : Energiya, 1973. 295 p.(Rus.).

Shagalova, S.L., Shnitser, I.N. Szhiganie tverdogo topliva v topkakh parogeneratorov. Leningrad : Energiya,1976. 220 p. (Rus.).

Bin-Hang Yan, Chen-Xi Cao, Yan Cheng, Yong Jin, Yi Cheng (2014). Experimental investigation on coal devolatilization at high temperatures with different heating rates. Fuel, Vol. 117. Part B. pp. 1215–1222.

ANSYS FLUENT 14.5 Theory Guide, (2012) ANSYS Inc.

Khzmalyan, D.M., Kogan, Ya.A. (1976) Teoriya goreniya i topochnye ustroistva. Moscow : Energiya. 488 p. (Rus.).

Nekhamin M.M., Bondzyk D.L. (2020). Parametri skorosti gorenia pri modelirovanii programoi ANSYS FLUENT procesa sjigsnia tverdogo topliva. [Combustion Speed Parameters when Simulating by ANSYS FLUENT Program of Solid Fuel Combustion]. Energotehnologii ta resursosberejenna. [Energy Technologies and Resource Saving]. No.1. pp. 41–45. DOI: 10 33070/etars.1.2020.05. (Rus.).

Osnovy prakticheskoi teorii goreniya. Ed. V.V.Po- merantsev. Leningrad : Energoatomizdat, 1986. 313 p. (Rus.).

Published
2020-09-20
How to Cite
Nekhamin, M. (2020). DESIGN BY PROGRAM ANSYS FLUENT PROCESSES IN HEATING OF CALDRON OF TPP-210А. Energy Technologies & Resource Saving, (3), 35-40. https://doi.org/10.33070/etars.3.2020.03
Section
Thermophysical basics of energy processes